Long Range RFID Card Reader EM / ID / IC Card RS232 / RS485 Wiegand 26

Long Range RFID Card Reader EM / ID / IC Card RS232 / RS485 Wiegand 26

Application of safe new /rfid/magnetic card collector

When the card approach the reader, the red light turn into green, after glinting to turn red color again, the buzzer sound shows transiting data.

It has 500ms proximity time distance for card proximity. After finishing card proximity, if the same ID card is still in the proximity range, reader will not send out the data, neither giving any sound hint.

But for Different ID card entering Proximity Area, Reader can do response continually and send out the data

RFID Reader products include : UHF Passive long distance rfid reader, Long range distance active 2.4G rfid reader, 4 channel and 4 port antenna long distance reader, EM 125KHZ long distance access control reader, Proximity EM 125Khz and 13.56Mhz access control wiegand card reader, stand alone rfid reader, PIN Reader, Keypad reader, USB Desktop reader, NFC Reader, Handheld reader writer, Magnetic reader, program rfid reader and writer,etc.

 

Advantages of the card reader

1) 5-16 V Operating voltages

2). International Standards Wigand 26Bits.

3). More than 50mm Reading Range

4). All in One Antenna

5). Support EM-ID or 13.56mhz Serial Number

6). External control Audio / Visual Indication: Internal LED and Buzzer

7). Optional Water-proof function for outside use.

 

Use reminds:

1. Confirm the electric voltage (DC12V) and differentiate positive anode and cathode of power supply

2. When external Power is used, make sure sharing the power with Controller Box or using the same GND

3. The wire connects reader to controller, advise use 8 cores stranded twisted pair cable(among them, three strands are spare, if no need reader show illegal card s by sound and light, LED wire can not be used, data wire Data1 Data0 are twisted pair would be better, we suggest sectional area are 0.22 square millimeter at least. The length should not exceed 100meters.

 

Product Parameter of card reader

	Item	RNCF-CR1
	Size	86x86x20mm
	Color	Black
	Metarials	ABS+Epoxy
	Voltage	DC9~12V
	Current	50mA
	Temperature	-25℃~85℃
	Reader speed	0.2sec
	Humidity	10%~90%
	Punch interval	0.5sec
	Waterproof	IP67
	Support	125KHz EM ID
		13.56MHz MF IC
	Frequency	125KHz/13.56MHz
Communication	Weigand26,Weigand34,RS232,RS485
Communication Distance	The weigand 100m
Built-in	Antenna,speaker,buzzer,red(bule)green color LED
Transmission	Weigand,RS232,RS485
Speical Provide	Logo printing,long cable,Reader module,Daul frequency(ID&IC)
Application	For access control ,attendance,fees,patrol,card,building onsay, parking systems, highways and rfid application.
Advantage	This series of reader with high sensitivity receiver,small operation current,single DC power supply,low price,and high reliability.
Introduction	Using + type screw driver to loosen the screw between the panel and motherboard. And then embed the motherboard to the side wall with the plastic plug and screws.
Wire Connection	Red DC 5V-16V
	Black GND
	Blue D1
	White D0
	Brown BEEP
	Green LED
	Yellow Alarm
Notice	1. Confirm the electric voltage (DC12V) and differentiate positive anode and cathode of power supply
	2. When external Power is used, make sure sharing the power with Controller Box or using the same GND
	3. When the distance between card reader and controller is more than 50m, please use Power Line with at least 1.5 square cm Dia, or using several parallel Network wires